Microprocessor Flame photometer

Microprocessor Flame photometer

Microprocessor Flame photometer

Salient Features:

• Microprocessor Based with Printer Interface
• Auto Gas Cutoff facility
• Auto Flame Failure Detection
• Five Measurements in Single Aspiration of the sample
• Calibration Curve Programmability Using Maximum of 5 Standard
• Data Processing Through Curve Fitting Techniques- Least Squares, Quadratic
• Multiple Calibration Curves Saving Facility
• Printer Attachment Facility
• Measurement can be done in ppm as well as in meq
• Setup Storage Facility (up to 10 setup files)
• Sample Data Storage Facility
• Direct Results in ppm and meq.
• Useful for both Medical & Soil Testing Applications

 

Microprocessor Flame Photometers 1600-G comes with Flame Failure detection and Auto Gas Cutoff Facility. In case of power failure, the gas cuts off automatically. In case the flame goes off accidently during work, the flame failure alarm sounds after a few seconds.

 

Microprocessor Flame Photometer 1600-G are used for the determination of Sodium, Potassium, Calcium, Lithium & Barium. They use the latest microcontroller technology and advanced engineering techniques so as to give enhanced accuracy and reproducibility. They have soft touch membrane keys for ease of operation. The solution is aspirated through an atomizer. Air, sample and the fuel are mixed in the mixing chamber which is then sprayed as a very fine mist into the flame. Radiations from the flame passes through specific narrow band interference filter and pass to the photo-detector. The final results are displayed on the 128 x 64 alphanumeric LCD. The standard model comes with 2 filters (Na, K). Additional filters Ca & Li are optional at extra cost.

 

A photoelectric flame photometer is a device used in inorganic chemical analysis to determine the concentration of certain metal ions.

 

MODEL

2600-G : sodium, Na,Potassium K

 1600-G : Sodium, potassium, calcium, lithium  

RANGE		General		Serum	Urine
	ppm		meq/l	meq/l	meq/l
	Na: 0 – 100		Upto 250 meq/l,	Na: 0 – 200	Na: 0 – 250
	ppm		1:100 dil.	1:100 dil	1:100 dil
	K: 0 – 100 ppm		Upto 250 meq/l,	K:0–100	K:0–100
			1:100 dil	1:100 dil	1:100 dil
RANGE	Ca: 0 – 100		Upto 250 meq/l,	–	Ca: 0 – 10
			1:100 dil	Li: 0 – 2	1:2 dil
	ppm
			Upto 250 meq/l,
				1:5 dil	–
			1:100 dil
	Li: 0 – 100 ppm
			–
	Ba: 0 – 100
	ppm

 

 

Sensitivity

 

General: Na: 0.5 ppm, K: 0.5 ppm, Ca: 15 ppm, Li: 0.5 ppm, Ba: 30 ppm

 

 

Filters	Na & K supplied (Ca, Li and Ba are optional at extra cost) {Ba can be factory
	fitted only}
Resolution	0.1 ppm/0.1 meq
Reproducibility	< 1% coefficient of variation for 20 consecutive samples using 10 ppm Na set as
	maximum standard
Linearity	< 2% error when 3 ppm Na/K and 5 ppm Li are set as maximum standard
Curve Fit	< 2% of FS
Accuracy
Display	128x64 Alphanumeric LCD with backlit
Average Time	In-built in software
Flame System	LPG and Dry Oil Free Sir
Detector	Silicon Photodiode
Calibration	Up to 5 Point Calibration with Curve Fitting Software
Gas Control	Adjustable with knobs
Flame Failure	Auto Detection
Gas Cutoff	Automatic
Ignition System	Auto Ignition
Automiser	Axial flow type
Printer	Provision for attachment of dot matrix printer or HP LaserJet/ inkjet (non-
	windows) printers with USB interface
Power	230 V ± 10% AC, 50 Hz

 

 

Dimensions

 

285 x 255 x 210 mm (L x B x H) (Approx.)

 

 

Weight

 

7.5 Kg (Approx.)

 

 

 

 

COMPRESSOR UNIT

 

 

	Air Supply	By oil free mini compressor unit with pressure regulator
	Combustion Gas	LPG controlled by precision regulator
	Power	230 V ± 10% AC, 50 Hz
	Dimensions	290 x 255 x 210 mm (L x B x H) (Approx.)
	Weight	8 Kg (Approx.)
		ACCESSORIES
	Power Cord	1 Unit
	AIR PIPE	1 Unit (Air Tubing with end clamps)
	GAS PIPE	1 Unit
	WASTE WATER PIPE	1 Unit
	BEAKER BOX	1 Unit (Contains 5 Beakers)
	CHIMNEY	1 Unit
	INSTRUCTION	1 Unit
	MANUAL
	CAPILLARY PIPES	3 Unit

 

 

Note: Specifications are subject to change due to continuous improvements.